Yuna is a 12HP Eurorack voice module with a face of her own. Her voice is a formant synthesizer that follows your pitch CV, and her face lives on a 1.54-inch screen above the controls. She works on her own: no other module, app, account, or internet connection is needed.
She has two sides, chosen with one lever:
CHAT: she idles on screen and now and then says one of 500 short lines, out loud, through her main output.
PERF: she becomes your grooving partner. Her synth voice plays through the output and she dances on screen, without interruption, for as long as you play.
The SHH button quiets her in either mode.
In the box
Yuna, 12HP
Eurorack power cable
Four M3 mounting screws
A card with the web address of this manual
Format
Eurorack, 3U, 12HP, 28 mm deep
Power
+12 V 150 mA · −12 V 15 mA · +5 V 0 mA
Sound
Formant voice synthesizer, 16 voices, 11 chords, 5 vowels plus RAW
Turn your case off before connecting or removing any module. Connect the power cable with the red stripe on the −12V side, both at Yuna and at your bus board. The header is shrouded and keyed, and Yuna has reverse-polarity protection, but a cable made up the wrong way round can still cause damage, and reversed power is not covered by the warranty.
The red stripe marks −12V. Match it at both ends.
Make sure your case has 12HP free.
Plug the cable into Yuna first, red stripe to −12V (marked on the back of the board).
Plug the other end into a free bus header, red stripe to −12V.
Fit Yuna in the rails and fix it with the four M3 screws. Tighten them only until snug.
Turn on the case. Yuna plays her boot clip and settles into the mode the lever is set to.
The microSD card on the back of the board holds her face and her spoken lines. Leave it in place: without it the screen stays dark.
Panel tour
Everything Yuna does is on the panel. There are no menus and no hidden settings, and every knob and jack does something.
Yuna’s front panel.
Control
What it does
Screen
Her face. Shows what she is doing: idling, talking, dancing, or dozing.
CHAT / PERF lever
Left = CHAT (spoken lines). Right = PERF (her synth voice, dancing).
SHH button
Tap to quiet her in either mode; tap again to release. The LED is lit while she is shushed. Hold for 2 seconds to set her glide (see Glide).
CHORD knob
Picks a chord, from a single note up through 11 chords.
VOICE knob
Picks one of 16 voices.
PITCH knob
Sets her note over 4 octaves (about 6° of turn per semitone). Sets her glide instead while the SHH LED is blinking.
VOWEL knob
Morphs AH → EH → EE → OH → OO. The last bit clockwise is RAW.
Attenuverters
One above each CV jack. Noon = that CV does nothing. Clockwise (+) adds the CV, counterclockwise (−) adds it upside down.
CV inputs
CHORD, PITCH, VOICE, and VOWEL. Each modulates the knob above it, scaled by its attenuverter.
CLOCK
Each pulse adds an accent, a vowel “wah” flick, and an arpeggio step when a chord is on.
GATE
When patched, she sounds only while the gate is high.
V/OCT
Pitch CV, 1 volt per octave from 0 V up, added to the PITCH knob.
OUT
Her audio output, at full Eurorack level (up to about 10 V peak to peak). To record her, go through an output module or mixer, or turn your interface’s input gain right down, or she will clip.
A note on the knobs: like most 9 mm pots, each knob does its work between about 8 o’clock and 4 o’clock. The first and last stretch of travel holds the end setting, so every voice, vowel, and chord is reachable before the knob hits its stop.
Modes
The lever picks what she does; SHH quiets her in either position.
One lever, one button, three ways to be.
CHAT
PERF
SHH
What you hear at OUT
Her spoken lines
Her synth voice
Nothing
What you see
Idle face, lines, reactions
Nonstop dancing
Idle face
Reacts to cables and knocks
Yes
No
Knocks only
Gets sleepy
Yes
No
Yes
CHAT
She idles, and every 31 to 60 seconds she says a line. There are 500 of them, and none repeats within 25 lines. Her synth voice is silent in CHAT, so the only sound at OUT is her talking. If a clock is patched, she waits for a clock pulse before speaking, so lines land in time with your patch.
She also says a quick hello exactly 3 seconds after you switch from PERF to CHAT, release SHH, plug a cable into OUT, or power on in CHAT. That makes her easy to demo.
PERF
Her synth voice plays through OUT and she dances on screen without interruption. PERF is her stage: no reactions, no lines, no dozing off. She keeps dancing even when nothing is playing.
SHH
Tap SHH and she goes quiet and idles, whichever way the lever points. It acts when you let go of the button; holding it for 2 seconds sets her glide instead. She can still get sleepy, and a knock on the case still startles or wakes her, silently. Tap SHH again to bring her back. In CHAT she greets you 3 seconds later.
Her voice
In PERF, Yuna is a formant voice synthesizer: a source sound shaped by vocal-tract filters into vowels. Four knobs shape her, and each has a CV input with its own attenuverter.
PITCH and V/OCT
PITCH sets her note over 4 octaves. Patch a 1 V/oct pitch CV into V/OCT to play her from a sequencer or keyboard; it adds to the knob. With nothing patched into V/OCT, the input is ignored. V/OCT reads 0 V and up; anything below 0 V plays as 0 V.
Glide
Her notes slide into each other a little, the way a singer scoops into a note. You can set how much:
Hold SHH for 2 seconds, until its LED starts blinking.
Turn PITCH. Fully counterclockwise is no glide, noon is the default, and fully clockwise is a long slide. The LED blinks faster as you add more. Her pitch stays put while you do this.
Tap SHH to finish. That tap doesn’t shush her. If you leave the knob alone for 10 seconds, she finishes on her own.
After you finish, PITCH holds her note until you turn the knob back to where it was, so her pitch never jumps. Glide returns to the default each time she powers on.
With GATE patched, a note that starts after a pause lands right on pitch, and only connected notes slide. Glide can’t be set while a cable is in the PITCH CV jack, because the knob and that jack are read together; the LED won’t blink.
VOICE: 16 sounds
Turn VOICE clockwise to move from human voices, through ensembles and eerie sounds, to machine voices, bass, and effects.
#
Voice
Character
01
DIVA
Pressed, bright voice with vibrato
02
POP CHOP
Bright, chopped; each gate is a hit (patch GATE)
03
BREATH
Breathy, half whisper
04
ALTO
Warm mid voice
05
LOW
Low, soft voice
06
CHANT
Big, dark, steady, with a sub
07
CHOIR PAD
Wide, detuned ensemble
08
GHOST
Soft, wavering, eerie
09
TALKBOX
Resonant, talkbox-style
10
VOCODER
Square-wave ensemble, robotic
11
DAFT
Ringing, slightly crushed robot voice
12
THROAT
Overtone whistle over a voice
13
ACID
Squelchy, very resonant; comes alive with CLOCK
14
FORM BASS
Growling formant bass with a sub
15
ALIEN
Ring-modulated, metallic
16
RAVE LEAD
Big detuned lead with vibrato
Changing voice crossfades smoothly, so you can sweep VOICE during a performance.
VOWEL and RAW
VOWEL morphs continuously through AH, EH, EE, OH, and OO. The last stretch clockwise is RAW: the source sound with the vowel filters bypassed. RAW is available only while nothing is patched into the VOWEL CV jack, so a VOWEL CV always stays within the vowels.
CHORD
Fully counterclockwise she plays a single note. Turning CHORD clockwise steps through 11 chords, voiced from low to high in the style of Mutable Instruments Plaits. With a clock patched, each pulse steps an arpeggio through the chord.
CV inputs
Each CV input adds to the knob above it, scaled by its attenuverter. At noon the CV has no effect; turn clockwise for normal modulation, counterclockwise for inverted. An empty CV jack does nothing.
Gate and clock
GATE decides when she sounds; CLOCK decides how she moves. Neither is required.
GATE
Nothing patched: she drones continuously, like an oscillator.
Gate patched: she sounds only while the gate is high, with a short, click-free attack and release. Unplugging the cable returns her to the drone straight away. A note that starts after a pause lands right on pitch instead of gliding.
Chop voices (POP CHOP, and lighter on CHANT, TALKBOX, ACID, and FORM BASS): each new gate is a punchy hit that swoops up into the vowel, like a sung “la” or “ya”, then settles to a lower sustain.
CLOCK
A clock never silences her. Each pulse adds an accent, a quick vowel “wah” flick, and one arpeggio step through the current chord when CHORD is on. ACID’s squelch depends on the clock, so it sounds tame until you patch one. In CHAT, a patched clock also times her spoken lines: she waits for the next pulse before speaking. Her hello lines don’t wait.
Her character
In CHAT and SHH, Yuna notices what goes on around her. None of these reactions make a sound at OUT, apart from her spoken lines.
Left alone, she gets sleepy.
She notices
What she does
When
A cable plugged into any jack except OUT
Glances at it
CHAT, while idle; at most once a minute
A cable plugged into OUT
Says hello 3 seconds later
CHAT
A firm knock on the case
Startles
CHAT or SHH, while idle; then waits 30 seconds before startling again
No one touching her for 30 minutes
Yawns
CHAT or SHH
35 minutes
Gets drowsy
CHAT or SHH
40 minutes
Falls asleep
CHAT or SHH
A touch, a cable, or a knock while drowsy or asleep
Wakes up
CHAT or SHH
To see the startle, keep your hands off the knobs and jacks for 2 seconds, then knock firmly on the case. She ignores knocks right after you touch a control, so ordinary patching doesn’t set her off.
Once in a long while, about as rarely as any single line, she leans in for a close look at you instead of speaking.
Patch ideas
Start with the lever on PERF, SHH off, and OUT patched to your mixer.
Drone. Nothing else patched. Pick a voice, set PITCH, and sweep VOWEL slowly by hand.
Sequenced voice line. A sequencer’s pitch CV into V/OCT and its gates into GATE. Try POP CHOP or TALKBOX for a sung, “la-la” line. Tied notes glide, separate notes land clean; set the amount with glide.
Club chords. A clock into CLOCK, CHORD turned up, and RAVE LEAD or DAFT. Each pulse steps an arpeggio and flicks the vowel.
Acid bass. ACID or FORM BASS, PITCH low, a clock into CLOCK, and sequencer gates into GATE. Turn VOWEL for the squelch.
Talking filter. A slow LFO into the VOWEL CV, attenuverter about halfway clockwise. She morphs through the vowels on her own.
Voice morph. A slow random or stepped CV into the VOICE CV, attenuverter turned up a little, to drift between neighbouring voices.
CHAT in the patch. Lever on CHAT with a clock patched: she speaks her lines in time with your clock, through the same OUT.
Firmware updates
Yuna’s firmware updates over the USB-C port on the back of the board. New firmware will be posted on the support page.
Keep Yuna powered from your case. USB does not power the board.
Connect the USB-C port to your computer with a data cable, not a charge-only cable.
Put her in update mode: hold the BOOT button on the back of the board (between the microSD slot and USB-C), switch the case off and on again, then release BOOT.
Flash the file with dfu-util -a 0 -s 0x08000000:leave -D yuna_voice.bin
Look for “File downloaded successfully”. An “Error during download get_status” message right at the end is harmless.
Yuna restarts by herself and plays her boot clip.
Updating the firmware never touches the microSD card, so her face and lines stay as they are.
Troubleshooting
Symptom
Check
Screen dark, no sound
Case power on? Power cable seated at both ends, red stripe to −12V? microSD card fully in?
No sound in PERF
SHH LED lit? Tap SHH. GATE patched with no gates arriving? Unplug GATE to hear the drone.
No sound in CHAT
Normal between lines: she speaks every 31 to 60 seconds. With a clock patched she waits for a pulse, so check the clock is running.
A knob does nothing near its ends
Normal: each knob works between about 8 and 4 o’clock.
A CV input does nothing
Attenuverter at noon? Turn it either way.
RAW is missing from VOWEL
RAW is off while a cable is in the VOWEL CV jack.
Pitch doesn’t follow the sequencer
Cable in V/OCT, not the PITCH CV jack? The PITCH CV jack is scaled by its attenuverter.
A knock doesn’t startle her
She must be idle in CHAT or SHH, with hands off the controls for 2 seconds. Wait 30 seconds after a startle. It never happens in PERF.
She doesn’t react to cables
Glances happen in CHAT only, at most once a minute.
Notes slide into each other
That’s her glide. Turn it down: hold SHH for 2 seconds, then turn PITCH counterclockwise. With GATE patched, notes after a pause don’t slide.
The SHH LED is blinking
She’s in glide setting. Tap SHH to finish, or wait 10 seconds.
PITCH does nothing
After setting glide, PITCH holds her note until you turn the knob back to where it was. Sweep it slowly through its range.
Holding SHH doesn’t start glide setting
Unplug the PITCH CV jack first.
Still stuck? The contact form comes straight to me.
Specifications and support
Format
Eurorack, 3U, 12HP (60.6 × 128.5 mm)
Depth
28 mm behind the panel
Power draw
+12 V 150 mA · −12 V 15 mA · +5 V 0 mA
Output
Up to about 10 V peak to peak
V/OCT
1 V per octave, 0 V and up
Panel
Aluminium, purple, with white and gold print
Screen
1.54-inch colour LCD
Firmware
Updatable over USB-C
Connectivity
None: no wireless, no microphone, no internet, and no account
Care
Keep Yuna dry and away from heat. Clean the panel with a soft, dry cloth. Don’t press on the screen. Leave the microSD card in place.
Warranty
Yuna is covered for 1 year from the date of your order, and the warranty transfers with the module. If she fails in normal use, we will repair or replace her. You ship her to us; in the US we pay the return shipping. The warranty does not cover reversed power, voltages outside the Eurorack standard, physical damage, modifications, or normal wear. Full terms are on the warranty page.
How Yuna was made
No AI runs on the module. Her voice is synthesized on board, and she works offline with no microphone, account, or cloud. Her face and her speaking voice were made with licensed generative AI tools, then chosen, edited, and sequenced by hand. Her speaking voice is a designed synthetic voice, not a copy of any real person. Every line she says was written or edited by hand. Her circuits and firmware were developed with AI coding help.
Yuna is made by Living Music Machines LLC in New York. Patent pending.